CHEREAU : After-Sales training centre
To guarantee the best level of service and maintenance for our customers’ equipment, we offer various training courses at our CHEREAU Service Centres and to our customers with their own workshop. The first type of course is general training for maintenance and servicing of CHEREAY equipment and the second is customised according to specific needs.
In addition to standard training, we have added two new courses, details of which you can find below.
Target public:
Our training courses are designed for body builders and/or electromechanical technicians who have already completed a course in electricity and/or bodywork or have experience in one of these fields.
These sessions are available in French. (English and any other language upon request).
Duration:
Our courses take place over 4 days, (30.5 hours) for general training courses and over 2 days, (16 hours) for specific courses.
Location:
The training courses take place at our CHEREAU Services repair workshop in Ducey (ZI Le Domaine, 50220 Ducey).
Organization and training:
CHEREAU is referenced and registered under No.25 50 00078 50 with the DIRECCTE*. Training courses can therefore be covered by your company’s training contribution.
* This registration does not constitute State approval.”
A complete training manual is given at the end of each session.
The quality certification was issued under the following category of action: Training actions
THE GENERAL TRAINING MODULES:
- Polyester repair
- Body assembly
- Rear end
- Electricity
- Touching up paintwork
- CHEREAU innovations
SPECIFIC TRAINING MODULES:
1. SMARTOPEN-C
- Factory tour
- Doors & partitions
- Bottom repair
- Bodywork and VIP panels
- Custody
- Paint fitting
- Electrical work
2. ELECTRICAL ARCHITECTURE
- NEXT multiplexing
- Gearbox
- Connect Box
- Carrier architecture
2024 SESSIONS:
- January : 09 and 10 january 2024 (smartOpen-C training)
- 16 to 19 january 2024 (standard training)
- February : 06 and 07 february 2024 (smartOpen-C training)
- 08 and 09 february 2024 (electrical architecture training)
- March : 26 and 27 march 2024 (smartOpen-C training)
- 12 to 15 march 2024 (standard training)
- April : 09 and 10 april 2024 (smartOpen-C training)
- May : 28 and 29 may 2024 (smartOpen-C training)
- 14 to 17 may 2024 (standard training)
- June : 11 and 12 june 2024 (smartOpen-C training)
- 13 and 14 june 2024 (electrical architecture training)
- September : 03 and 04 september 2024 (smartOpen-C training)
- 10 to 13 september 2024 (standard training)
- October : 08 and 09 october 2024 (smartOpen-C training)
- 10 and 11 october 2024 (electrical architecture training)
- November : 05 and 06 october 2024 (smartOpen-C training)
- 19 to 22 november 2024 (standard training)
- December : 10 and 11 december 2024 (smartOpen-C training)
WHAT IS QUALIOPI, THE PAC* QUALITY GUARANTEE MARK?
Stakes:
Contribute to facilitating the choice of a PAC by individuals and companies; Impel a dynamic of continuous improvement of the processes implemented by PACs.
Objectives:
Single quality certification issued by independent certifiers, allowing the use of public or mutualized funds;
Legibility of the training offer for the public, by associating the quality certification with a brand.
Terms of delivery:
The certification process is rigorous and standardized. It allows to obtain a right to use the brand. The certification is issued by certifying bodies accredited or in the process of being accredited by Cofrac* on the basis of the single national reference system mentioned in article L. 6316-3 of the French Labor Code.
This certification can also be issued by a labeling body recognized by France Compétences on the basis of the same reference system.
*(Providers of actions contributing to the development of skills within the framework of training actions, skills assessments, actions allowing the validation of acquired experience, training actions through apprenticeship)
*Cofrac: French Accreditation Committee
SATISFACTION RATE / SUCCESS RATE
In 2023, the various trainees trained evaluated our training courses at 3.9/4 (content, achievement of objectives, quality of the support given, duration, general organization, quality of the animation, trainer relationship).
Our trainers evaluated the trainees on their level of technical knowledge at the end of the training. It is 87% on average (against 43% on arrival)
Are you interested in a CHEREAU training session?
